Installing a Socket in Plasterboard Funny

The content of the article

1. Peculiarities
2. Tools
3. Montage with your own hands
4. Installation of converters
5. Installing the outlet and switch
6. Equipment
7. Tips and recommendations

Recently, the walls of the walls of the plasterboard enjoys great popularity. It is not only convenient and easy, but also inexpensive, besides, plasterboard helps to hide all the irregularities of the walls. However, it is worth the issue of installing sockets. To do this correctly, you need to carefully examine the question.

Peculiarities

Installation of outlets in plasterboard is slightly different from other repair processes. To successfully perform work, it is necessary to choose the right sockets and switches. And it is also necessary to pay attention to the submersion. They differ slightly from those installed in concrete or brick walls.

Their peculiarity is that they are complemented by clamping paws that are installed on the screws. Rotating them, you can move the paws along the housing. As for switches and sockets, they are produced in standard sizes. And purchasing all the necessary elements, it is necessary to check whether they coincide.

It must be remembered that the socket is electrical displacement, and therefore, when installing it, it is necessary to adhere to the safety regulations. If there is no self-confidence, then it is necessary to charge this work to specialists.

All installation work must be carried out when electricity is disabled. All wiring must be checked for voltage. It is impossible to touch the bare wires. These are simple security rules, what you can not forget not to risk your life and health.

To install a rosette in plasterboard, you need to have all the necessary tools.

1. Perforator or drill, With the help of which all the necessary holes are done. Since the standard sizes of the conversion – sixty-eight millimeters, the diameter of the cutter on a drill or a perforator must be the same.
2. Screwdrivers. One – Figured Outlet Installation, Other – Indicator, To Check Voltage.
3. Marker, To accurately note where the socket will be located.
4. Level. If you wish, you can even use short, because the sockets are very small in size.
5. Chisel and hammer, which are used in cases if you need to reflect a metal profile.

This minimum set of tools is enough to install sockets in a drywall room.

Montage with your own hands

In order to install a rosette in drywall, first need to make markup. The next step will be the installation on a drill of a pre-prepared nozzle. Then with its help carved through hole in the GRA. To make it easier to facilitate the work, you can use the usual drill. And it is worth considering that When working with a drill, you do not need to push it hard to it, as this can lead to the formation of torn edges in the hole.

Fastening the socket in a plasterboard wall can be made without nozzle. It will be longer and harder. This uses a regular knife. They need to cut through the thickness of the drywall.

One of the most frequent problems that occur during the installation of conversion is the possibility of getting into the profile to which plasterboard is attached. To avoid this, you need to make an extra room for pickle. Make it possible with a chisel and hammer. To do this, cutting out a piece of profile.

To put a double or triple outlet, you need to do between the holes of the jumper. As in the case of the usual model, before installing, it is necessary to make marking. Select the place where the socket itself will be, and its center is marked. Then through this point the horizontal line is carried out.

Next, seventy-two millimeters are measured from the first point and put a mark where the second hole will be. Marks is done as much as there are sockets in the block, and the distance between them should be the same. Then cut holes. As a result, jumpers are three millimeters thick.

Installation of converters

Before installing, it is necessary to do the hole where the wires will be held. Further through the mounting box you need to stretch the wire. It must be put in the hole and fix with paws. But it is also necessary to know that some boxes have a groove with a smooth transition. Therefore, it turns out that near the bottom of the submerged foot is almost drowned in the groove. However, when the screw is spinning, it slowly protrudes over the riding. This allows you to consolidate.

There is another kind of boxes having a smooth groove. Here so that the legs do not interfere, special niches are made for them, where they are hiding. To mount such a peavercraft, it is necessary to monitor the legs when installing it into the hole in the niches. Further, the box turns so that the foot is vertically, and the foot from the lower screw performed over the case itself. So that she could not change their position, it should be tightened with screw.

Next, you need to turn the opposite one hundred eighty degrees, and pull out the second paw from the niche. And only then both paws stretch and fix the box.

Installing the outlet and switch

In order to install a switch or a socket, first you need to de-energize the wiring and shorten so that the supply remains to fifteen centimeters long. After you need to clean her ends. From the switch removed the upper part and the bolts weaken. Need not to confuse them when fixing. This also applies to three-core wiring, which has a ground wire. If there is no special contact in the outlet or switch, then it just hides inside the box. Before this, it needs to be well inized.

Attaching the zero and phase wire, it is important to fasten the bolts on the contacts. After the connection is done, you need to install the inner part of the socket or switch to the opposite. On it is fixed with screws.

Equipment

Installing an emission allows you to attach the supply water supply to the desired instruments. The principle of operation of such an element of the power grid is to transfer water pressure from water supply to a specific crane. What allows you to change the mixers at any time. Equipment there are different species.

1. Single, which are used to connect only one highway.
2. Solid double – they apply to connect two highways at once together.
3. Double having a relief board. Such vehicles are installed at some distance from each other. They are attached to a special bracket.

Materials required for vehicle – these are colored and ferrous metals. To install them, it is necessary that the distance between the ends was at least fifteen centimeters. The diameter of the hole in the wall must match the size of the desired part. Be sure to make a markup before starting work, and then drill holes. Them should be three pieces.

Further on the reverse surface of the alternate tires glue and only then it is attached to the wall and pulls up with the help of screws. The space that was formed between the wall and the outlet can be filled with putty.

After the socket is fixed and connected to the network, it can be safely used.

If everything is done correctly, then the submersion will not be overwhelmed over time, and it will not be necessary to carry out installation works.

Tips and recommendations

If the setting is made with your own hands, it is necessary to listen to the advice of specialists.

Installation is better to do even before plasterboard itself. First install a frame of methockrofil, which is fixed on the wall surface. To protect the wires, you can use a corrugated pipe.

To bring the current to the outlet, you need to use a three-in-room cable having a double winding. If used to fix the segment of the copper wire, then it will give the design of reliability.

And it is worth remembering that, installing sockets, you need to take into account not only your needs, but also taken by all building rates. For example, install the outlet must not lower than thirty centimeters above the floor. For the switch, the floor height should be approximately ninety centimeters, and at least fifteen centimeters from the door.

But if the electrical devices are located in other places, then the sockets can be placed where the most convenient. For example, in the kitchen, most comfortable will be located right above the table. At the same time, the location of the socket must be at least one hundred and twenty centimeters from the floor, and at least thirty centimeters from the door. This will allow you to connect devices without using carrying.

But also, if the TV is placed directly on the wall, you can hide the outlet behind it. Such accommodation pleases and practicality, and an attractive appearance. In the bathroom it will correctly put a socket for sixty centimeters from the floor. But if it serves to connect a washing machine, the height should be at least one meter.

larkinscaughts.blogspot.com

Source: https://comfortables.info/repair/subtleties-installation-of-outlets-in-plasterboard.html

Share this post